Features1With low speed and high torque, good performance. 2Twoway communication, you can check the power of the scooter through the remote control. 3Multiple protections, with low voltage alarm function, undervoltage and power failure protection. 4The sinusoid solution makes it more stable than ESC and not easy to burn out. 5Suitable for scooters, unicycles, balance scooters.SpecificationItem type:Scooter Controller SetMaterial: Electronic components + ABSColor: As picture shownWeight: Approx. 280gDrive mode: dual system driveInduction method: for hallController type and performanceController TypesTotal power of controllerControl electric quantityT2 wireless dual driveDC voltage 36V/24V1300W2Control motor type and performanceMotor typeMaximum power of motorMotor speedCan not connect the motor for hallDC Brushless MotorWithin 650WWithin 8000 rpmcan not connectMaximum power: 430W (36V)Speed: 4200 RPMMaximum speed: 35KM/HCarrying weight: 120KGLong-distance distance: up to 20 metersProtection: overvoltage, undervoltage, overheating, stall, CW/CCW, adjustable speedCurrent: 12ARemote control built-in lithium batteryThe capacity of the remote control: 400MAHTotal length of remote control: Approx. 12cm/4.7inRemote control length: Approx. 6cm/2.4inCircuit board size: Approx. 10.5x8cm/4.1x3.1inApplication areas: scooters, unicycles, balance scootersSuitable for hub motor model airplane motor 5055 5065 6354 6364 6374 6384How to choose the right controller:6 series battery is 25.2V, 7 series battery is 29.4V, 10 series battery is 36V2. Confirm the motor typeExternal motor, chain, belt drive, use belt controllerHub motor, motor integrated wheel, please select the controller with the word hub3. Confirm single-drive dual-drive or four-wheel driveA controller drives a motor is a single driveOne controller drives two motors is dual driveOne controller drives four motors is four-wheel driveTaboo: Do not connect motor cables in parallel to allow single drive to drive two motorsElectric four-wheel scooter control system:Adopting the sinusoidscheme, the performance is more stable than the ESC, and it is not easy to burn outDescription of matching signal between remote control and main controller:1. Connect the main controller to the power supply.2. Turn on the power, wait for two seconds and then press and hold the key for about 6 seconds, let go when the switch indicator flashes.3. Turn on the remote control switch and use a small screwdriver to press the button in the small hole in the lower left corner of the remote control.4. Turn off the remote control and turn it on for two seconds. Wait for the remote control signal light and the switch signal light to flash at the same time to indicate that the configuration is successful.About the motor for hall wire connection description:At present, the normal version and standard version of the controller need to provide conventional connection methods for the phase sequence. The brushless motor is controlled by 3 phases and 6 ways. 3 for hall states correspond to 3 motor wires and 6 output states. There are 36 connections for different combinations. , Among them, there are 6 kinds of connections that can make the motor run normally, and 3 of these 6 kinds of connections are forward rotation and the other 3 are reverse rotation.1. Motor wire blue to controller blue, motor wire green to controller green, motor wire yellow to controller yellow.2. The blue of the motor wire is blue to the controller, the green of the motor wire is yellow to the controller, and the yellow of the motor wire is green to the controller.3. Motor wire yellow to controller yellow, motor wire blue to controller green, motor wire green to controller blue.4. Motor wire green to controller green, motor wire blue to controller yellow, motor wire yellow to controller blue.5. Motor wire blue to controller yellow, motor wire yellow to controller green, motor wire green to controller blue.6. Motor wire yellow to controller blue, motor wire blue to controller green, motor wire green to controller yellow.Generally, the controller is placed on the top and the motor is placed on the bottom1.) Color vs. Color2.) Blue to blue, the other 2 colors are reversed3.) Yellow to yellow, the other 2 colors are reversed4.) Green to green, the other 2 colors are reversed5.) Top blue to bottom blue, the other 2 colors are reversed6.) Top yellow to bottom blue, the other 2 colors are reversedfor hall has positive and negative, indicating that the motor has a phase angle of 60 Degree, and if there is no positive and negative, it is a 120 Degree phase angle. It can be put in as it is (you can use instantglue to fix it slightly), connect the positive and negative poles of the three Halls in parallel and connect them with the thin red and black wires of the motor lead wire. Weld (pay attention to the insulation). Connect the signal wires of the three Halls Connect with the thin yellow, green and blue wires of the motor lead wires respectiv