DC 6-60V 16A 400W 3 Phases Hall Brushless Motor Controller Board BLDC PWM PLC Driver Module With Forward/Reverse/Brake Function

22,95 €
+ 11,99 € Doručenie

DC 6-60V 16A 400W 3 Phases Hall Brushless Motor Controller Board BLDC PWM PLC Driver Module With Forward/Reverse/Brake Function

  • Značka: Unbranded

DC 6-60V 16A 400W 3 Phases Hall Brushless Motor Controller Board BLDC PWM PLC Driver Module With Forward/Reverse/Brake Function

  • Značka: Unbranded
Odporúčaná cena: 149,00 €
Cena: 22,95 €
Ušetrili ste: 126,05 € (84%)
Predáva:
22,95 €
+ 11,99 € Doručenie

Na sklade

Akceptujeme nasledovné platobné metódy

Popis

DC 6-60V 16A 400W 3 Phases Hall Brushless Motor Controller Board BLDC PWM PLC Driver Module With Forward/Reverse/Brake Function Features: _x000D_ _x000D_ 1.MA MB MC phase line output connection motor _x000D_ 2. 5V GND motherboard comes with 5V power supply (current does not exceed 30MA) _x000D_ 3.VCC GND motor main power supply (external DC power supply) _x000D_ 4.SC speed pulse signal output _x000D_ 5 positive and negative reversing control interface (also can be connected to the external switch) _x000D_ 6.VR speed control signal input (onboard with potentiometer speed control can also be connected to 0-5V analog simulation PWM duty cycle to support dual signal input speed regulation) _x000D_ 7.Ha Hb Hc +5V GND Hall signal Power input, generally with Hall's motor has five corresponding lines _x000D_ _x000D_ Full patch process Stable performance with positive/reverse function _x000D_ _x000D_ Tips: _x000D_ _x000D_ After receiving the goods, there are generally 5 Hall wiring lines on the brushless motor. Two of them are the Hall power supply lines. The three Hall signal lines must be distinguished. Especially, the power supply lines must not be mistaken. The sequence on the board must match the sequence of the three phase lines on the motor driver board to work properly. If you do not know the definition of the Hall wire, you can debug the low voltage and current at the first power on. Change the order of the Hall line until normal operation, do not use large current, high voltage debugging, if the Hall line is not connected in sequence, the high voltage and high current test machine, there is the risk of damage to the MOS tube, if the three Hall signal lines The motor is running smoothly and smoothly. The low-speed start is stable and the torque is large. If the three Hall signal lines are not connected, the following characteristics are available: 1 The motor cannot be started normally or the start-up is difficult (sometimes it is necessary to manually turn the motor to start) 2 The motor starts to shake with no power. _x000D_ _x000D_ Motherboard specifications: _x000D_ _x000D_ Product Name: 450W Brushless Hall DC Motor Driver _x000D_ Model Number: ZS-X11D1 _x000D_ Operating voltage: 9-60V _x000D_ Maximum current: rated 16A peak 20A _x000D_ Maximum power: 450W _x000D_ Overcurrent protection: Yes _x000D_ Product size: length 63MM* width 45MM* height 28MM _x000D_ Weight: about 93g. _x000D_ _x000D_ Precautions: _x000D_ _x000D_ 1. The power supply circuit on the main board has no fuse, and the built-in self-addition will cause permanent damage to the chip on the board (even 2 seconds is not allowed). _x000D_ 2. During normal operation, there is sampling overcurrent protection at the motor output. Since the module power and current are very large, please do not short circuit when the module is not working normally. Once the short circuit has the possibility of burning the line, the first wiring test machine Please use small current and low voltage test, after ok, then pass high current and high voltage, because it is bare board module for sale, pay attention to the wiring line insulation, strong voltage is not allowed to touch the board parts. _x000D_ 3. Do not connect the motor that is obviously inconsistent with the voltage and current of the drive module or is far away from the motor to avoid inexplicable damage. _x000D_ _x000D_ _x000D_
  • Fruugo ID: 417073103-880115877
  • EAN: 7559728652594

Informácie o bezpečnosti produktu

Prečítajte si informácie o bezpečnosti produktu špecifické pre tento produkt uvedené nižšie

Nasledujúce informácie poskytuje nezávislý maloobchodný predajca tretej strany, ktorý predáva tento produkt.

Bezpečnostné štítky produktu

CE Mark
Bezpečnostné upozornenia: WARNING! TO AVOID DANGER OF SUFFOCATION,KEEP AWAY FROM BABIES ANDCHILDREN. DO NOT USE IN CRIBS/BEDSOR PLAY PENS.THIS BAG IS NOT ATOY.
Ingrediencie: Octinoxate 3.3383%
Číslo dielu výrobcu: HC300872
Číslo modelu: HC858112
Sériové číslo: HC003352
Číslo šarže: HC001432

Dodanie a vrátenie

Odoslané do 3 dní

  • EXPRESS: 11,99 € - Doručenie do pi 26 septembra 2025 - Najlacnejšie - Najrýchlejší

  • STANDARD: 11,99 € - Doručenie medzi ut 07 októbra 2025–pi 17 októbra 2025

Doručenie od Čína.

Snažíme sa, aby sme výrobky, ktoré si objednáte, doručili celkom v súlade s vašou špecifikáciou. Ak by ste však dostali neúplnú objednávku alebo iný tovar ako ten, ktorý ste si objednali, alebo existuje nejaký iný dôvod, prečo nie ste s objednávkou spokojní, môžete objednávku alebo niektoré produkty z nej vrátiť a za tovar dostať plnú náhradu. Pozrite si všetky pravidlá vrátenia

Podrobnosti o zhode produktu

Pozrite si informácie o súlade špecifické pre tento produkt uvedené nižšie.

Nasledujúce informácie poskytuje nezávislý maloobchodný predajca tretej strany, ktorý predáva tento produkt.

Výrobca:
Nižšie sa nachádzajú kontaktné informácie výrobcu príslušného produktu, ktorý sa predáva na Fruugo.

  • Ningbo Sida Yuandong Import & Export
  • Ningbo Sida Yuandong Import & Export Co., Ltd.
  • No. 360 Shengmo Road, Qiuai Town, Yinzhou District Ningbo
  • Ningbo
  • China
  • 315101
  • pyls55967@163.com
  • 17719951355
  • https://www.fruugo.co.uk/search?merchantId=15958

Zodpovedná osoba v EÚ:
Nižšie sa nachádzajú kontaktné informácie zodpovednej osoby v EÚ. Zodpovedná osoba je určený hospodársky subjekt so sídlom v EÚ, zodpovedný za dodržiavanie povinností súvisiacich s príslušným produktom, ktorý sa predáva na území Európskej únie.

  • EC REP SERVICES SL
  • EC REP SERVICES SL
  • Calle Gran Via 49, 7 DCH.
  • Madrid
  • Spain
  • 28013
  • ECREPSERVICE@HOTMAIL.COM
  • 34682797075